€242.51*
Available, delivery time: 1–3 weeks (delivery in even calendar week in BE, FR, LU, NL)
Queenply. The original
- extremely light — extremely stable
- carrier board with 11 layers (thickness 15 mm)
- waterproof thanks to Kaurit gluing
- calibrated to an accuracy of 0.2 mm
- made from sustainably grown wood
Queenply lightweight panel. Wood veneer aspen oak. Unique decor. In several thicknesses.
Characteristic for panel boards with aspen oak veneer are the natural growth cracks, which we leave in the wood for reasons of uniqueness and design. These cracks are therefore not an unsightly blemish in the veneer, but exactly what characterizes the aste oak.
If you like this naturalness, then you should take a closer look at our Queenply with aste oak veneer. It can be used to build great furniture for the van. Queenply, which is coated on one side, is suitable for use as a wall or ceiling covering in vans or yachts for example.
Due to its unbeatably low weight of 320 – 350 kg/m³, this panel is very easy to work with. And in a van you also save a lot of weight and fuel.
All other important technical properties of this veneer and panel can be found here in the product description under “Technical Details”.
Please note: Due to the specific properties of the wood, there may be small open knots in the veneer in one place or another. This is due to the nature of the wood itself and is not a reason for complaint.
| Carrier plate: | Queenply with 11 layers (15 mm thickness) |
|---|---|
| Format: | 248 × 121 cm |
| Thickness: | 16 mm |
| Weight: | 17,54 kg |
| Coating: | Veneer |
The weight of the base panel of Queenply knotty oak veneer remains unbeatable: approx. 320 – 350 kg/m³. The veneer is also about 50% lighter compared to HPL coating. We achieve the high screw pull-out strength and the particularly good staying power through the multiplex construction – which makes it easier for you to work on your van interior.
Our 4 mm Queenply with knotty oak veneer is veneered on one side. You can use this lightweight board for your wall and ceiling paneling in vans or boats, for example. On the other hand, Queenply veneered on both sides in higher thickness is ideal for furniture construction.
We calibrate the carrier panels accurate to 0.2 mm, which reduces the thickness tolerance and ensures a better surface smoothness.
The gluing is MR (moisture resistant).
The veneer is moisture-regulating. It absorbs moisture better and releases it later. This optimizes the indoor climate in the camper. Therefore, this lightweight panel is suitable not only for motorhome finishing, but also for the interior finishing of yachts and ships.
You are interested in the Queenply coated on one side? A good choice! However, we would like to point out that these panels can tend to warp slightly due to the one-sided coating and the associated asymmetrical structure. Even we cannot change this. Therefore, a possible warpage is not a reason for complaint.
Plywood multiplexture beams such as the Queenply with oak veneer do not have the same surface properties as chipboard or MDF beams. Any surface irregularities that may occur are in the nature of the substrate and are not grounds for complaint.
We also take great care to ensure that your ordered Queenply panels leave our factory in perfect condition and arrive undamaged. You can rely on that! However, we would also like to point out that any distortion of the boards caused by transport or further storage is not grounds for complaint.
As you may already know, veneers are a natural product made of wood and are therefore always unique. That is what makes them so unique. However, this is also the reason why our veneers shown in the shop are only exemplary representations and slightly deviating surfaces are also in the nature of things. Please take this into account in your planning and selection.
When processing the veneer, please ensure that you take adequate safety precautions, such as extracting the chips and wearing safety goggles and a protective mask.
Due to the low weight of the Queenply, there is an increased dust formation during processing.
And another important note: We pack your finishing panels with special care before shipping and make sure that they leave our warehouse without any damage to the edges. However, even with the greatest care, it can happen during transport that a corner is pressed in or the edge is slightly damaged. We know that too. That’s why we calculate 1 cm less for each side of every Queenply finishing panel in advance: 249 cm × 121 cm for the raw panel, 243 cm × 121 cm for all composite elements and 247 cm × 120 cm for all veneered panels. This saves us all a lot of time that would otherwise be wasted on complaints. Put this time into your project – and feel free to recommend us to others.
You are interested in the Queenply coated on one side? A good choice! However, we would like to point out that these panels can tend to warp slightly due to the one-sided coating and the associated asymmetrical structure.
Even we cannot change this. Therefore, a possible warpage is not a reason for complaint.
Maintenance Oil
