Queenply Lamitech Burgundy 2158
€9.95
Please notice: this HPL sample (strength: 0.9 mm) is delivered without a carrier board.
Product information "Queenply Lamitech Burgundy 2158"
Lamitech HPL = highest quality. Color: Burgundy red. Variants OPAK and MATT. Combined with Queenply, of course.
You are looking for a deep, slightly elegant HPL color? Then this burgundy red might be just the right color for your extension plans. Whether as a splash of color or for larger areas: both is possible. And what is also important: you will hardly find a higher quality, more durable HPL. Why are we so sure?
Lamitech HPL is almost unbeatable in its combination of classy and robust: scratch-resistant, hard-wearing and therefore perfect for any vehicle interior, for homes, commercial areas and offices. We combine it with our best carrier panel: Queenply.
The difference between the two HPL surface variants OPAK and MATT:
Burgundy OPAK (extremely matt, anti-fingerprint): Premium HPL. Velvety soft touch. With anti-fingerprint effect. Water-repellent. Antimicrobial coating. Heat-resistant. Micro-scratches can be polished away with a dirt eraser sponge. Even coffee or wine stains are no problem.
For everyday use, in the office, when travelling: Backpacks, dogs, children, customer traffic - no scratches or marks remain on the surface. And it remains as beautiful as it was at the beginning. That's why it is suitable for kitchens, conference tables, catering areas, van conversions, interior fittings and much more.
Burgundy MATT (slightly pearl structure): High-quality HPL variant. Light pearl structure with matt effect. However, without anti-fingerprint finish. But just as hard-wearing. Antimicrobial coating. Water-repellent. Abrasion-resistant.
Why we offer two versions in our online shop?
Quite simply: the combination is not only practical, but also cost-saving. For cupboards, technical compartments and furniture construction. An anti-fingerprint coating is not necessarily required on the inside or on the back. So, if you choose the MATT surface in the same color for the back, it is more cost-effective, the design and color remain in line and you can be sure that you are still using an absolutely high-quality Lamitech surface.
Simply select variants when ordering! Whether the same coating on both sides or a mix: OPAK/OPAK or OPAK/MATT or MATT/MATT. You simply select via the buttons next to the product pictures: 1. thickness of the Queenply carrier panel. 2. surface variants. 3. the shopping basket.
Maybe you still need some more informations about Lamitech? Find it here or take a look at the technical details.
| Total strength: | 0.9 mm |
|---|---|
| Format: | Sample (Din A5) |
| Strength carrier board: | 0 mm |
| Surface Lamitech: | Opak |
| Weight: | 0,037 kg |
| Coating: | HPL |
| Material: | Compound element |
| Surface: | Extreme matt, Matt |
You can purchase Queenply with Lamitech HPL decor in various thicknesses from us. The total thickness of your Queen depends on whether you choose the MATT or OPAK surface variant or a mix of both. You will find the specifications below our product description once you have selected the thickness and surface.
A few words about the Lamitech decor (it's worth reading – promise!):
Surface variant OPAK:
This surface is extremely high quality. Super matt, light-absorbing, with an anti-fingerprint effect and a feel that will win you over. We are sure of this, because everyone who holds a sample in their hands feels the same way! The decor is also very durable, water-repellent, abrasion-resistant and easy to clean. Small micro-scratches caused by crockery or other items can be easily wiped away with a dirt eraser sponge. Wine stains or permanent marker can be removed in the same way. This makes OPAK the perfect choice for furniture fronts, kitchen or shop counters, table tops and much more.
Surface variant MATT (MT):
We also offer every Lamitech decor in a MATT version with a slight pearl structure. This is also high-quality, durable, water-repellent, easy to clean, hard-wearing and has an antimicrobial coating..
But why are we doing this? Quite simply – for you! This gives you a choice of two surface finishes in a perfect color combination. For example, you can build the outer fronts of your furniture using the highest quality OPAK finish and choose the slightly more affordable MATT finish in the same color for the inner sides. All on Queenply, of course…
So you have the choice, and once again we have what you need: OPAK on both sides, or OPAK/MATT, or MATT/MATT.
Just three steps to your customised panel
The selection process is very simple: 1. Select the thickness of the Queenply carrier panel. 2. Specify the desired surface variants. 3. Proceed to checkout.
Gluing
We glue our Queenply composite elements exclusively with high-quality PUR hot melt adhesive. We do not use white glue. PUR is waterproof and heat-resistant up to 135° Celsius. This means that the HPL does not peel off so quickly when exposed to heat.
Additional calibration
We calibrate the Queenply carrier panel once again at our factory to an accuracy of 0.2 mm. This means you can work with perfect gap dimensions during further processing and have no stress with thickness tolerances.
Screw pull-out strength
We always work in more centre layers into our Queenply than this is generally the case. This production method guarantees you significantly greater stability and a particularly high screw pull-out strength. Nevertheless, Queenply remains one of the lightest finishing panels on the market..
Cleaning and care
The HPL surface in MATT is easy to clean with all commercially available, non-abrasive liquid cleaning agents. You can use the surface cleaner recommended by us, for example. You’ll find it in our accessories section.
In addition, the matt HPL surface can be disinfected with all commercially available disinfectants.
You can clean our premium surface OPAK with a dirt eraser sponge and mild washing-up liquid. This also removes micro-scratches. However, to avoid damaging the super-matt anti-fingerprint surface, there are a few small things to bear in mind. So please take a look at the cleaning instructions for this special surface in advance.
Edging
Please note: These elements are unedged. The HPL may protrude at the sides. We have dispensed with the edging, as each panel has to be edged again by you before installation anyway. We therefore charge 1 cm less for each side of each composite element in advance (243 cm × 121 cm).
Storage
Of course you can store the panels for some time. Please make sure that you store them horizontally in a dry place and protect them from excessive temperature and humidity fluctuations as well as UV radiation.
Panel dimensions
244 cm x 122 cm
Plywood and multiplex beams such as Queenply do not have the same surface properties as chipboard or MDF beams. Any surface irregularities that may occur are in the nature of the substrate and are no reason for a complaint. Production or material-related minimal defects that do not affect the product quality and are permissible within the 1st choice are assessed according to the sorting regulations based on DIN EN 438 and the international ISO standardisation.
We also take great care to ensure that your ordered Queenply panels leave our factory in perfect condition and arrive undamaged. You can rely on that! However, we would also like to point out that any distortion of the panels caused by transport or further storage is not grounds for complaint.
Please note! Surface treatment before installation!
It is important to oil the raw surfaces of your Queenply before installation. This applies to all veneers and all panels coated only on one side, as well as to the raw panels and all open edges. Why? This makes our Queenply resistant, protects and maintains the wood. We also have a special recommendation for this, which you can order directly: RUBIO® Monocoat Maintenance Oil 2C. One coating is enough with this oil! You can find all informations here.
Surface color tone
Please also note that the representation of the HPL coloring on your screen may differ slightly from the original color! If you have any questions about this, simply contact us.
Occupational safety measures
If you are going to process our lightweight panels, please ensure that you take adequate safety precautions, such as extracting the chips and wearing protective goggles and a protective mask. Due to the low weight, there is an increased dust formation when processing the Queenply.
Edging
Please note: These elements are unedged. The HPL / acrylic may protrude at the sides. We have dispensed with the edging, as each panel has to be edged again by you before installation anyway. We therefore charge 1 cm less for each side of each composite element in advance (243 cm × 121 cm).
Transport damage
And another important note: We pack your panels with special care before shipping and make sure that they leave our warehouse without any damage to the edges. However, even with the greatest care, it can happen during transport that a corner is pressed in or the edge is slightly damaged. We know that, too. That’s why we calculate 1 cm less for each side of every Queenply finishing panel in advance: 249 cm × 121 cm for the raw panel, 243 cm × 121 cm for all composite elements and 247 cm × 120 cm for all veneered panels. This saves us all a lot of time that would otherwise be wasted on complaints. Put this time into your project – and feel free to recommend us to others.
